TechCalc100 for Designers, Architects ,Engineers and Technicians ( 6-19 users)

Description

TechCalc 100
Engineering/Scientific Software
100 technical calculation programs
ISBN: 978-0-941801-01-0 (one CD licensed for 6-19 users)
"Turn your calculating hours into seconds and make your time more productive. More power for your dollar!"
Used by Students, Designers, Engineers, Architects, and Educators.
Includes 100  frequently used calculation programs for
Mechanical, Structural, Electrical, Physics,  Architectural, and Manufacturing applications.
No need to rewrite equations or isolate unknown variables. Just enter known values in INPUT boxes and click ENTER for instant results. No need to spend time looking up formulas in expensive handbooks and performing calculations by longhand.
Special discounts for academic institutions. Please inquire.
Do you need to size a steel beam to support a concentrated load of  30,000 lbs. over a span of 10 feet?
Or how about sizing a woodbeam to support 10,000 lbs. over a span of 10 feet.
Do you need to size a hydraulic cylinder to push a load of 5000 lbs. at a 30 degree angle in 6 seconds and calculate gpm of hydraulic fluid required?
Do you need to calculate voltage drop in a two way line?
Do you need to design a square reinforced concrete footing to support a column load of 80,000 lbs?
Do you need to calculate torque required to accelerate a rotational mass?
How about sizing a reinforced concrete beam to support a uniform load of 50,000 lbs over a span of 10 feet?
These calculations and many more can be solved instantly by a keystroke.
TechCalc includes the following calculations:
(ACTUATOR)  Calculates hydraulic cylinder forces and flow requirements.
(BELTCONVEYOR)  Calculates total HP to drive a belt conveyor.
(SIMPLE BEAM)  Sizes a steel beam for a concentrated load (includes Beam Economy Table)
(RESIDENTIAL HEAT LOSS)  Calculates heat loss for a residence.
(ROCKET MOTOR)  Calculates rocket motor thrust.
(COOLING)  Calculates cooling/ventilation requirements for occupants in a building.
(SQUARE FOOTING)  Calculates allowable load  for a square reinforced concrete footing.
(STEEL COLUMN) Calculates allowable load on a column serving as a brace or strut.
(ENGINE)  Calculates engine horsepower,displacement, effective pressure.
(SOLIDSHAFT)  Calculates diameter, torque and angle of twist for a solid shaft.
(CAPACITIVEREACTANCE)  Calculates capacitive reactance based on hertz and farads.
(HEATRANSFER)  Calculates heat transfer through a material.
(HPTORQUERPM)  Calculates HP/Torque/RPM Relationships
(CIRCULARMIL)  Calculates circular mil area for a specified voltage drop.
(ORIFICE)  Calculates theorectical discharge of a liquid a square edged orifice.
(BEAMCONNECTION)  Calculates allowable loads for a bolted beam connection.
(PROJECTILE)  Calculates theorectical range of a projectile.
(SCREWCONVEYORHP)  Calculates total HP to drive a screw conveyor.
(ELECTRICALHP)  Calculates horsepower for single phase, two phase, three phase current.
(VBELT)  Calculates V-belt component relationships.
(WOODBEAM)  Calculates allowable distributed load for a pre-sized wood beam.
(AIRDUCT)  Calculates air duct size to transport air.
(LATHETIME)  Calculates lathe cutting time.
(EMF)  Calculates EMF of a DC generator.
(BOILER)  Calculates boiler fuel requirements.
(CRITICALSHAFT)  Calculates critical shaft speed.
(IMPEDANCE)  Calculates impedance in a coil based on hertz, ohms and henrys
(FANPOWER)  Calculates air flow, horsepower and minimum duct wall thickness.
(CONCRETEBEAM)  Calculates total uniform load for a reinforced concrete beam.
(DRILLTIME)  Calculates drilling time for drilling hole.
(HELICALSPRING)  Sizes a helical compression spring.
(PUMPHP)  Calculates brake HP input to a pump.
(INDUCTIVEREACTANCE)  Calculates inductive reactance.
(PIPEHEAT)  Calculates heat loss through insulated pipe.
(CONCRETECOLUMN)  Calculates allowable axial load on a square reinforced concrete column.
(SHIPROPELLER)  Calculates diameter of line shaft for ocean -going vessel.
(OHMS)  Calculates total OHMS of both wires in a electrical circuit
(VENTURI)  Calculates rate of flow through a Venturi Meter.
(BEARINGLOAD)  Calculates radial force on a shaft with V-Belt or Chain drive.
(CHAINDRIVE)  Calculates chain drive component relationships.
(MILLINGTIME)  Calculates milling cutting time.
(ELEVATORHP)  Calculates motor HP for an elevator load.
(FLYWHEEL)  Calculates velocity and energy output of a flywheel.
(UNIFORMBEAM)  Sizes a steel beam to support a uniformily distributed load.
(HOSESIZE)  Calculates minmum hose size required for hydraulic line.
(HOLLOWSHAFT)  Calculates maximum torque and HP transmitted by a hollow shaft.
(VOLTAGEDROP)  Calculates voltage drop in an circuit.
(NOZZLE)  Calculates jet velocity, quantity and force of water through a nozzle.
(WINDFORCE)  Calculates wind force against a flat surface.
(ROTATIONALMASS)  Calculates torque required to accelerate a rotational mass.
(ACCELERATION) Calculates acceleration time and velocity.
(AIRCORE) Calculates indutance value.
(BEND ALLOWANCE) Calculates length of bent metal.
(BIN FEEDER) Calculates HP for belt feeder.
(BOLTED JOINT) Calculates allowable load on single-bolted lap joint.
(CIRCULAR PLATE STRESS) Calculates bending stress for circular plate.
(COOLING COIL) Calculates cooling coil requirements.
(COUPLING) Sizes a rigid flange coupling to transmit HP.
(DIFFERENTIAL PULLEY) Calculates pull force to lift load.
(DRAWING) Calculates force for a drawing operation.
(ELECTRIC MOTOR HP) Calculates motor requirements to move load.
(ENGINE LATHE) calculates cutting time for screw thread operation.
(EXPANSION) Calculates change in material length due to temperature change.
(FEEDWATER HEATER) Calculates outlet temperature of water.
(FILLET WELD) Calculates length of weld to support load.
(FLUID POWER) Calculates HP to move hydraulic fluid.
(FREEFALL) Calculates period of time for object to fall to Earth.
(GASFLOW) Calculates flow rate and velocity of a gas through a pipe.
(HEATING) calculates quantity of fuel or energy required for heating.
(HEATING COIL) Calculates inside diameter for a steam heating coil.
(HOIST DRUM) calculates hoist drum requirements for lifting load.
(HYDROTURBINE) Calculates HP output of a hydraulic turbine.
(INCLINE FORCE) Calculates force required to pull load up an incline.
(KEYSTOCK) Calculates stresses in a predetermined key size.
(MAN VS MACHINE) Calculates cost comparison between man and machine for manufacturing a part.
(MOMENTUM) Calculates average driving force of a mass.
(PAN CONVEYOR) Calculates capacity and HP requirements.
(PIPE FLOW) Calculates flow through a pipe.
(PIPE SIZE) Calculates pipe size for liquid flow.
(PIPE WALL) Calculates pipe wall thickness.
(PUNCHING) Calculates punching force for round holes.
(RECTANGULAR PLATE) Calculates plate thickness for uniform load.
(REFRIGERATION) Calculates refrigeration load requirements.
(REYNOLDS) Calculates Reynold's number.
(ROOF VENT) Calculates required number of roof powered ventilators.
(ROTARY FEEDER) Calculates RPM of a rotary feeder to move load.
(SATELLITE) Calculates velocity of a satellite orbiting Earth.
(SLOPE ELEVATION) Calculates slope between elevation points.
(SMOKE STACK) Calculates height and diameter for a smoke stack.
(SPUR GEAR) Calculates number of teeth, pitch diameter, rpm and center distance.
(STEAM ENGINE HP) Calculates HP developed by pre-sized steam engine parts.
(STEAM PIPE) Calculates pipe diameter, steam velocity and pressure drop.
(STEAM TURBINE) Calculates HP for a steam turbine.
(STORAGE TANK) Calculates capacity of a storage tank.
(V-DIE) Calculates force to bend metal in V-Die.
(VEHICLE HP) Calculates HP required to drive a vehicle.
(WATER PRESSURE) Calculates water pressure at any height.
Requires MS Excel, CD drive
Calculations in English units only.
Free shipping in U.S.
Be sure to visit our eBay store for other items of interest.
http://www.stores.ebay.com/houseplansbydesignerswest
Thanks for visiting.
William